BLACKOUT SALE — 20% off select gear + free gifts. Shop the sale → BLACKOUT SALE: 20% off select gear. Shop →
Products
Mission Darkness™
Military-grade Faraday bags, forensic enclosures, tents, and EMP protection. Engineered and assembled in the USA.
View All Products →
Tents
CYPHERCYLENT™ Series
Room-scale RF isolation systems with TitanRF™ fabric, carbon fiber frames, and patent-pending magnetic door seals.
View All Tents →
Blog
News & Resources
Guides, tutorials, product deep-dives, and industry news from the Mission Darkness team.
View All Posts →
More
Company & Resources
Learn about Mission Darkness, our team, certifications, government programs, and how to work with us.
About Us →

Faraday analysis enclosure MDFB‑BBT‑PRO

BlockBox Touch Pro Instructions

Assembled BlockBox Touch Pro with two glove ports, a central shielded filter, a shielded window across the top and a carbon-fiber frame.

Operation

Operating the BlockBox Touch Pro

  1. Step 1: Verify shielding first

    Confirm no signal penetrates. Every session. Test the enclosure before any device goes in. Once the device is inside, confirm the signal is cut off and that the device is connected properly to receive power, if needed.

  2. Inside the enclosure: both conductive gloves hanging above the RF dampening foam, with the interior side of the shielded filter between them.

    Step 2: Seat the RF foam inside

    The RF dampening foam is the device platform and viewing stand. Seat it inside the enclosure.

  3. Operator sliding a laptop into the enclosure through the open rear closure.

    Step 3: Place the device inside

    Open the rear closure; set the device on the RF dampening foam, under the window.

  4. Hands rolling down the rear NeoLok closure of the enclosure.

    Step 4: Seal the enclosure

    Roll the NeoLok closure down; snap it shut to lock it.

  5. Top view of an operator's arms in both conductive gloves beneath the shielded window.

    Step 5: Operate through the gloves

    Work through both gloves, viewing through the window. Use the extraction tool inside the enclosure with the device.

  1. Step 6: When finished

    Disconnect, open, remove.

Care

Care and replacement

Cleaning and handling

  • Keep dry; wipe the exterior only with a damp rag.
  • Keep sharp objects off the Faraday fabric.
  • Medical gloves worn inside the conductive gloves can help keep them clean.

When to replace a shell or glove

  • Puncture or tear in the Faraday fabric
  • Contamination from an evidence scene
  • Tarnished or degraded Faraday layers
  • Failed shielding verification with no visible cause

Replacement procedures are in Instructions PDF, section C. Verify shielding before returning the unit to service.

Replacement parts

Keep your BBT-PRO in service.

The BlockBox Touch Pro is built to be serviced. Replace worn components individually, or restore the whole enclosure with one kit.

All-in-one

Full replacement kit

Kit includes

  • 1 Faraday shell
  • Installed mounting brackets
  • RF dampening foam
  • 2 conductive gloves (1 set)
  • 2 cable kits
  • Short Ethernet cable
  • Long Ethernet cable
  • 2 styluses
  • 3 mm Torx L-key
  • Instruction sheet

Individual replacement parts

  • Conductive gloves2 conductive gloves (one set)
  • Front plateGlove plate, install hardware and 2 glove clamps
  • Filter plateFilter plate with Multiport filter installed. Custom filters available.
  • Faraday shell1 Faraday shell, mounting brackets and 3 mm Torx L-key
  • Cables & accessories2 cable kits, short and long Ethernet cables, 2 styluses and 3 mm Torx L-key
  • StandBBT-PRO stand
  • RF foamReplacement RF foam
  • Custom filtersContact us for custom filter options and quotes.

BlockBox Touch Pro Instructions